View LC5545LD_9092005.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

sanken electric co., ltd. http://www.sanken-ele.co.jp/en/ lc5540ld series descriptionthe lc5540ld series is the power ic for the isolated type led driver which has an incorporated power mosfet, designed for input capacitorless applications, and making it possible for systems to comply with the harmonics standard (iec61000-3-2 class c), even during light load condition. the controller adapts the average current control method for realizing high power factors, and the quasi-resonant topol- ogy contributes to high efficiency and low emi noise. the series is housed in dip8 packages. the rich set of protection features helps to realize low com- ponent counts, and high performance-to-cost power supply. the incorporated mosfet has a v dss (min) rating from 650 v (LC5545LD and lc5546ld) to 800 v (lc5548ld). the r ds(on) (max) is 1.9 (lc5546ld) to 3.95 (LC5545LD). it is capable of a maximum output power of 20 w on 230 vac supply to 16 w on universal input supply (85 to 265 vac) (lc5546ld) based on the thermal rating. note that the maximum output power can be up to 120% to 140% of this value. however, it may be limited in applica- tions with low output voltage or short duty cycle. features and benefits integrated on-time control circuit (it realizes high power factor by average current control) integrated startup circuit (no external startup circuit necessary) integrated soft-start circuit (reduces power stress during start-up on the incorporated power mosfet and output rectifier) integrated bias assist circuit (improves startup performance, suppresses vcc voltage droop during operation, and allows use of low-rated ceramic capacitor on vcc pin) integrated leading edge blanking (leb) circuit integrated maximum on-time limit circuit protection features: ? overcurrent protection (ocp): pulse-by-pulse ? overvoltage protection (ovp): latched shutdown ? overload protection (olp): latched shutdown ? thermal shutdown (tsd): latched shutdown single-stage power factor corrected off-line switching regulator ics typical application package: 8-pin dip not to scale c2 c6 c5 d8 + - pc1 u2 dz1 d1d3 d2d4 f1 l1 c1 q1 d5 c4 c3 t1 d6 d7 dz2 pc2 l2 led r1 pc2 d9 r8 r9 r10 r11 r12 r13 r14 r15 r16 r17 r18 r19 r20 r ocp r3 r4 r5 r6 vac p c1 r7 r21 dz3 c18 c7 c8 c10 c9 c11 c12 c13 c14 c15 c16 c17 5 1 2 3 d/st 8 s/gnd vcc controller chip u1 ovp ocp fb nc s/gnd lc554xld 6 4 applications led lighting fixtures led light bulbs lc5540ld-ds january 28, 2013 downloaded from: http:///
2 sanken electric co., ltd. lc5540ld-ds single-stage power factor corrected off-line switching regulator ics lc5540ld series january 28, 2013 selection guide part number mosfet v dss (min) (v) r ds(on) (max) ( ) pwm operation frequency, f osc (typ) (khz) on-time t on(max) (typ) ( s) p out * (w) 230 vac 85 to 265 vac LC5545LD 650 3.95 72 9.3 13 10 lc5546ld 1.9 60 11.2 20 16 lc5548ld 800 3.5 72 9.3 13 10 *based on the thermal rating; the allowable maximum output power can be up to 120% to 140% of this value. however, maximum output power may be limited in such an application with low output voltage or short duty cycle. absolute maximum ratings unless specifically noted, t a is 25c characteristic symbol notes pins rating unit drain current 1 i dpeak LC5545LD single pulse 8 C 1 2.5 a lc5546ld 4.0 a lc5548ld 2.6 a single pulse avalanche energy 2 e as LC5545LD i lpeak = 2.0 a, v dd = 99 v, l = 20 mh 8 C 1 47 mj lc5546ld i lpeak = 2.7 a, v dd = 99 v, l = 20 mh 86 mj lc5548ld i lpeak = 2.3 a, v dd = 99 v, l = 20 mh 56 mj control part input voltage v cc 2 C 1 35 v ocp pin voltage v ocp 3 C 1 ? 2.0 to 5.0 v fb pin voltage v fb 4 C 1 ? 0.3 to 7.0 v ovp pin voltage v ovp 6 C 1 ? 0.3 to 5.0 v allowable power dissipation of mosfet 3 p d1 mounted on a 15 mm 15 mm pcb 8 C 1 0.97 w operating ambient temperature t op D? 55 to 125 c storage temperature t stg D? 55 to 125 c channel temperature t ch D 150 c 1 refer to mosfet safe operating area curve. 2 refer to mosfet avalanche energy derating coefficient curve. 3 refer to mosfet temperature versus power dissipation curve. the polarity value for current specifies a sink as "+," and a source as ? , referencing the ic. downloaded from: http:///
3 sanken electric co., ltd. lc5540ld-ds single-stage power factor corrected off-line switching regulator ics lc5540ld series january 28, 2013 electrical characteristics of control part t a = 25c, v cc = 20 v, unless otherwise specified characteristic symbol test conditions pins min. typ. max. unit power supply startup operation operation start voltage v cc(on) 2 C 1 13.8 15.1 17.3 v operation stop voltage* v cc(off) 2 C 1 8.4 9.4 10.7 v circuit current in operation i cc(on) 2 C 1 C C 4.7 ma startup circuit operation voltage v startup 8 C 1 18 21 24 v startup current i cc(startup) v cc = 13 v 2 C 1 ? 8.5 ? 4.0 ? 1.5 ma startup current threshold biasing voltage* v cc(bias) 2 C 1 9.5 11.0 12.5 v normal operation pwm operation frequency f osc LC5545LD 8 C 1 60 72 84 khz lc5546ld 50 60 70 khz lc5548ld 60 72 84 khz maximum on-time t on(max) LC5545LD 8 C 1 8.0 9.3 11.2 s lc5546ld 9.0 11.2 13.4 s lc5548ld 8.0 9.3 11.2 s fb pin control minimum voltage v fb(min) 4 C 1 0.50 0.85 1.20 v maximum feedback current i fb(max) 4 C 1 C40 C25 C10 a leading edge blanking time t on(leb) 3 C 1 ? 600 ? ns quasi-resonant operation threshold voltage-1 v bd(th1) 3 C 1 0.14 0.24 0.34 v quasi-resonant operation threshold voltage-2 v bd(th2) 3 C 1 0.11 0.16 0.21 v protection operation ocp pin overcurrent protection (ocp) threshold voltage v ocp 3 C 1 ? 0.66 ? 0.60 ? 0.54 v ocp pin source current i ocp 3 C 1 ? 120 ? 40 ? 10 a ocp pin overvoltage protection (ovp) operation voltage v bd(ovp) 3 C 1 2.2 2.6 3.0 v overload protection (olp) threshold voltage v fb(olp) 4 C 1 4.1 4.5 4.9 v ovp pin ovp threshold voltage v ovp(ovp) 6 C 1 1.6 2.0 2.4 v vcc pin ovp threshold voltage v cc(ovp) 2 C 1 28.5 31.5 34.0 v thermal shutdown activating temperature t j(tsd) C 135 C C c *v cc(bias) > v cc(off) always. downloaded from: http:///
4 sanken electric co., ltd. lc5540ld-ds single-stage power factor corrected off-line switching regulator ics lc5540ld series january 28, 2013 electrical characteristics of mosfet t a = 25c, unless otherwise specified characteristic symbol test conditions pins min. typ. max. unit drain-to-source breakdown voltage v dss LC5545LD 8 C 1 650 DD v lc5546ld 650 DD v lc5548ld 800 DD v drain leakage current i dss 8 C 1 DD 300 a on-resistance r ds(on) LC5545LD 8 C 1 DD 3.95 lc5546ld DD 1.9 lc5548ld DD 3.5 switching time t r LC5545LD 8 C 1 DD 250 ns lc5546ld DD 400 ns lc5548ld DD 400 ns thermal resistance r ch-c LC5545LD between channel and case; case temperature, t c , measured at the center of the case top surface D DD 42 c/w lc5546ld DD 35.5 c/w lc5548ld DD 40 c/w downloaded from: http:///
5 sanken electric co., ltd. lc5540ld-ds single-stage power factor corrected off-line switching regulator ics lc5540ld series january 28, 2013 10 1 0.1 0.01 transient thermal resistance, r ch-c (c/w) transient thermal resistance curve time (s) 10 C6 10 C5 10 C4 10 C3 10 C2 10 C1 ambient temperature, t a (c) 1.21.0 0.8 0.6 0.4 0.2 0 0 255075 125 100 150 mosfet temperature versus power dissipation curve allowable power dissipation, p d1 (w) channel temperature, t ch (c) 100 8060 40 20 0 25 50 75 125 100 150 eas temperature derating coefficient (%) mosfet avalanche energy derating coefficient curve drain-to-source voltage, v ds (v) 100 10 1 0.1 0.01 1 10 100 1000 drain current, i d (a) mosfet safe operating area curve drain current limited by on-resistance 1 ms 0.1 ms to use this graph, apply the s.o.a temperature derating coefficient taken from the graph at the left t a = 25c, single pulse channel temperature, t ch (c) 100 8060 40 20 0 0 25 50 75 125 100 150 safe operating area temperature derating coefficient (%) s. o. a. temperature derating coefficient curve characteristic performance LC5545LD downloaded from: http:///
6 sanken electric co., ltd. lc5540ld-ds single-stage power factor corrected off-line switching regulator ics lc5540ld series january 28, 2013 10 1 0.1 0.01 transient thermal resistance, r ch-c (c/w) transient thermal resistance curve time (s) 10 C6 10 C5 10 C4 10 C3 10 C2 10 C1 ambient temperature, t a (c) 1.21.0 0.8 0.6 0.4 0.2 0 0 255075 125 100 150 mosfet temperature versus power dissipation curve allowable power dissipation, p d1 (w) channel temperature, t ch (c) 100 8060 40 20 0 25 50 75 125 100 150 eas temperature derating coefficient (%) mosfet avalanche energy derating coefficient curve drain-to-source voltage, v ds (v) 100 10 1 0.1 0.01 1 10 100 1000 drain current, i d (a) mosfet safe operating area curve drain current limited by on-resistance 1 ms 0.1 ms to use this graph, apply the s.o.a temperature derating coefficient taken from the graph at the left t a = 25c, single pulse channel temperature, t ch (c) 100 8060 40 20 0 0 25 50 75 125 100 150 safe operating area temperature derating coefficient (%) s. o. a. temperature derating coefficient curve characteristic performance lc5546ld downloaded from: http:///
7 sanken electric co., ltd. lc5540ld-ds single-stage power factor corrected off-line switching regulator ics lc5540ld series january 28, 2013 10 1 0.1 0.01 transient thermal resistance, r ch-c (c/w) transient thermal resistance curve time (s) 10 C6 10 C5 10 C4 10 C3 10 C2 10 C1 ambient temperature, t a (c) 1.21.0 0.8 0.6 0.4 0.2 0 0 255075 125 100 150 mosfet temperature versus power dissipation curve allowable power dissipation, p d1 (w) channel temperature, t ch (c) 100 8060 40 20 0 25 50 75 125 100 150 eas temperature derating coefficient (%) mosfet avalanche energy derating coefficient curve drain-to-source voltage, v ds (v) 100 10 1 0.1 0.01 1 10 100 1000 drain current, i d (a) mosfet safe operating area curve drain current limited by on-resistance 1 ms 0.1 ms to use this graph, apply the s.o.a temperature derating coefficient taken from the graph at the left t a = 25c, single pulse channel temperature, t ch (c) 100 8060 40 20 0 0 25 50 75 125 100 150 safe operating area temperature derating coefficient (%) s. o. a. temperature derating coefficient curve characteristic performance lc5548ld downloaded from: http:///
8 sanken electric co., ltd. lc5540ld-ds single-stage power factor corrected off-line switching regulator ics lc5540ld series january 28, 2013 functional block diagram functional block diagram functional block diagram pin-out diagram pin list table number name function 1 s/gnd mosfet source and gnd pin for the control part 2 vcc supply voltage input and overvoltage protection (ovp) signal input 3 ocp overcurrent protection (ocp), quasi-resonant signal input, and overvoltage protection (ovp) signal input 4 fb feedback signal input and overload protection (olp) signal input 5n f no function; must be externally connected to s/gnd pin with as short a trace as possible, for stable operation of the ic 6 ovp overvoltage protection (ovp) signal input 7 C pin removed 8 d/st mosfet drain pin and input of the startup current 12 3 4 8 65 d/st ovp nf s/gnd vcc ocp fb s/gnd tsd leb d/st control part start up reg bias uvlo vcc ocp ovp ovp osc ocp detection bottom reg control feedback olp drv fb q s r nf downloaded from: http:///
9 sanken electric co., ltd. lc5540ld-ds single-stage power factor corrected off-line switching regulator ics lc5540ld series january 28, 2013 package outline drawing, dip8 0 . 2 5 + 0 . 1 - 0 . 0 5 6.5 1 4 5 8 9.4 0.3 0.5 0.1 0.89 typ 4.2 0.3 3.3 3.4 0.1 0.2 (7.6 typ) 2.54 typ -0.05 -0.05 0.2 0.5 7.5 +0.3 +0.3 1.0 1.52 a lc b c a: part #: 554xb: lot number 3 digits, plus l 1 st letter: last digit of year 2 nd letter: month jan to september: numeric october: o november: n december: d 3 rd letter: week date 1 to 10: 1 date 11 to 20: 2 date 21 to 31: 3 c: sanken control number unit mm pb-free. device composition compliant with the rohs directive. downloaded from: http:///
10 sanken electric co., ltd. lc5540ld-ds single-stage power factor corrected off-line switching regulator ics lc5540ld series january 28, 2013 because reliability can be affected adversely by improper storage environments and handling methods, please observe the following cautions. cautions for storage ensure that storage conditions comply with the standard temperature (5c to 35c) and the standard relative humidity (around 40% to 75%); avoid storage locations that experience extreme changes in temperature or humidity. avoid locations where dust or harmful gases are present and avoid direct sunlight. reinspect for rust on leads and solderability of the products that have been stored for a long time. cautions for testing and handling when tests are carried out during inspection testing and other standard test periods, protect the products from power surges from the testing device, shorts between the product pins, and wrong connections. ensure all test parameters are within the ratings specified by sanken for the products. remarks about using silicone grease with a heatsink when silicone grease is used in mounting the products on a heatsink, it shall be applied evenly and thinly. if more silicone grease than required is applied, it may produce excess stress. volatile-type silicone greases may crack after long periods of time, resulting in reduced heat radiation effect. silicone greases with low consistency (hard grease) may cause cracks in the mold resin when screwing the products to a heatsink. our recommended silicone greases for heat radiation purposes, which will not cause any adverse effect on the product life, are indicated below: type suppliers g746 shin-etsu chemical co., ltd. yg6260 momentive performance materials inc. sc102 dow corning toray co., ltd. soldering when soldering the products, please be sure to minimize the working time, within the following limits: 2605c 101 s (flow, 2 times) 38010c 3.50.5 s (soldering iron, 1 time) soldering should be at a distance of at least 1.5 mm from the body of the products. electrostatic discharge when handling the products, the operator must be grounded. grounded wrist straps worn should have at least 1 m of resistance from the operator to ground to prevent shock hazard, and it should be placed near the operator. workbenches where the products are handled should be grounded and be provided with conductive table and floor mats. when using measuring equipment such as a curve tracer, the equipment should be grounded. when soldering the products, the head of soldering irons or the solder bath must be grounded in order to prevent leak voltages generated by them from being applied to the products. the products should always be stored and transported in sanken shipping containers or conductive containers, or be wrapped in aluminum foil. downloaded from: http:///
11 sanken electric co., ltd. lc5540ld-ds single-stage power factor corrected off-line switching regulator ics lc5540ld series january 28, 2013 the contents in this document are subject to changes, for improvement and other purposes, without notice. make sure that this is the latest revision of the document before use. application and operation examples described in this document are quoted for the sole purpose of reference for the use of the prod- ucts herein and sanken can assume no responsibility for any infringement of industrial property rights, intellectual property rights or any other rights of sanken or any third party which may result from its use. unless otherwise agreed in writing by sanken, sanken makes no warranties of any kind, whether express or implied, as to the products, including product merchantability, and fitness for a particular purpose and special environment, and the information, including its accuracy, usefulness, and reliability, included in this document. although sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of semicon- ductor products at a certain rate is inevitable. users of sanken products are requested to take, at their own risk, preventative measures including safety design of the equipment or systems against any possible injury, death, fires or damages to the society due to device failure or malfunction. sanken products listed in this document are designed and intended for the use as components in general purpose electronic equip- ment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). when considering the use of sanken products in the applications where higher reliability is required (transportation equipment and its control systems, traffic signal control systems or equipment, fire/crime alarm systems, various safety devices, etc.), and whenever long life expectancy is required even in general purpose electronic equipment or apparatus, please contact your nearest sanken sales representative to discuss, prior to the use of the products herein. the use of sanken products without the written consent of sanken in the applications where extremely high reliability is required (aerospace equipment, nuclear power control systems, life support systems, etc.) is strictly prohibited. in the case that you use sanken products or design your products by using sanken products, the reliability largely depends on the degree of derating to be made to the rated values. derating may be interpreted as a case that an operation range is set by derating the load from each rated value or surge voltage or noise is considered for derating in order to assure or improve the reliability. in general, derating factors include electric stresses such as electric voltage, electric current, electric power etc., environmental stresses such as ambient temperature, humidity etc. and thermal stress caused due to self-heating of semiconductor products. for these stresses, instantaneous values, maximum values and minimum values must be taken into consideration. in addition, it should be noted that since power devices or ic's including power devices have large self-heating value, the degree of derating of junction temperature affects the reliability significantly. when using the products specified herein by either (i) combining other products or materials therewith or (ii) physically, chemically or otherwise processing or treating the products, please duly consider all possible risks that may result from all such uses in advance and proceed therewith at your own responsibility. anti radioactive ray design is not considered for the products listed herein. sanken assumes no responsibility for any troubles, such as dropping products caused during transportation out of sanken's distribu- tion network. the contents in this document must not be transcribed or copied without sanken's written consent. downloaded from: http:///

▲Up To Search▲

Price & Availability of LC5545LD

	To Download LC5545LD Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .